US Flag, Interment 4' 6" x 7'

Discussion in 'US Flag Specs and Design' started by ir.hondo, Jun 15, 2011.

  1. ir.hondo

    ir.hondo New Member

    US Flag, Interment 4' 6" x 7' (NON - STANDARD)

    I have posted this thread (Listed Below) on other areas of these forums but Ihave added information on the box the flag came in: It was made by FITZHUGH CORRUGATED. I have done a Google search on this company and found nothing. Went to The Thomas Register and they are not listed in the Registry. Half of their stamp is covered by the Address Label so that is all the information I can get off the box. The Address Label from the VA in Winston Salem, NC to the Postmaster in Warsaw, NC (which has no zip codes - zip codes started on July 1, 1963). About 25% -30% of the label is missing (Left side mid-way down to about 55% - 60% across the label) but on the lower right of the label I can make out 1956 GPO 1959 O - 45909-- (the final part of the number is missing). Any help in identifying this flag would be appreciated. I would like to know why it is an odd ball size, when it was manufactured (years) and the exact use of it (See below on information listed in the write up I found on the internet at an odd ball site - do not remember the site name. It was just a sentance or two ).


    Information Posted on other Forums:
    I am new to this form and just recently purchased a 50 Star flag (4-1/2 x 7 ft. U. S. Flag, Interment) from a local Military Store I have the box it came in and on one side of the outside of the box it has the following:

    8345-082-6584
    5_F-4018
    4-1/2 X 7 U. S. Flag, Interment
    50 Star
    1 each
    Valley Forge Flag, Co.
    Sinking Springs, Pa.
    Sinking Springs is correct (it is in smaller print than the other information - had to use a magnifying glass in order to read it)

    The other side has:
    Veterans Administration
    Winston Salem, NC
    Addressed to Postmaster, Warsaw, NC
    Their are no zip codes on the box in the addresses.

    The flag has an identification tag sewn on it and the information is:
    "BEST" 2x2 PLY
    100% Cotton-Bunting
    Valley Forge Flag Co.
    Spring City, PA

    Inside the box is a V A Form 10-2893 dated JAN 1958. (That shows some age due to some minor fading of the printing on the paper and the paper is starting to get brittle)
    The return address on the form is:
    Veterans Administration
    Central Office
    Washington 25, D. C.
    and is addressed to:
    Manager
    Veterans Administration Supply Depot
    P. O. Box 27
    Hines, Illinois
    Again no zip codes. There is a hand written note on the form stating, "Does not need to be return PER/VET. Administration, Oct. 21, 2008 in Illinois."

    The stars on the flag are stitched (sewn on), Matter of fact the whole flag with all the stripes are stitched (sewn together). I would like to be able to properly identify this flag and the time frame it was made in, as it is not listed as a standard size in the Marine or Air Force Flag manuals for any type of flag. The standard casket interment flag is 5 ft. x 9 ft. 6 in. One thing the flag has never been folded in a triangle, it was just folded in a rectangle to fit it the box. The box is 3.25" (Height) x 9.25" (Length) x 6" (Width). Also, the box has been flatten to some extent as if something heavier was on top of it and flattened it down due to the weight for some time. I did find one small article (a odd ball site) while doing a Google search that this size flag had two uses, one was to fly at small Military installations and the second to drape over a veterans casket. But I can not find anywhere else any information on this size/type flag. the time frame it was manfactured in and other than that article that this size flag was used to drape over a veterans casket of fly at a small Military installation. Would any one be able to help me in this matter? Any information will be greatly appreciated.
    Thanks,
     
  2. csaanv

    csaanv Member

    Hi ir.hondo,
    Could you give us a photo? My family is from that area around Warsaw.
    mike
     
  3. usvetsnet

    usvetsnet New Member

    Attached Files:

  4. pinkrosi

    pinkrosi New Member

    There are, of course, more companies than just "Valley Forge" that manufacture "G-Spec" Flags. Two others that come to mind are CF Flag and Annin & Co. I know that there are other companies that manufacture, or who have in the past manufactured, "G-Spec" Flags, I just can't remember them right off the top of my head right now.
     

Share This Page